Post Stock Login Register

EN 10025-3 S500 vs AS/NZS Grade 500

Strong Match — 92.4% match based on chemical composition and mechanical property overlap.

EN 10025-3 S500 (EN 10025-3:2019) and AS/NZS Grade 500 (AS/NZS 3597:2008) are both steel grades. Both fall under the Structural Steel category. EN 10025-3 S500 is typically used for used in heavy structural sections, mining equipment, bridge fabrication, transport vehicles, and offshore structures., while AS/NZS Grade 500 is commonly used for heavy mining equipment, bulldozer blades, wear-resistant structural applications, large crane booms, offshore jackets.. EN 10025-3 S500 is defined under European Standard (EN), originating from Europe, while AS/NZS Grade 500 is defined under Australian/New Zealand Standard (AS/NZS), originating from Australia/New Zealand.

As per chemical composition, EN 10025-3 S500 vs AS/NZS Grade 500 is a 92.4% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a strong match overall at 92.4%.

Frequently Compared With EN 10025-3 S500:
CSA G40.21 480W CSA G40.21 400W CSA G40.21 260W AS/NZS 3679.1 300 GOST 19281 09G2S AS/NZS 3679.1 350 ASTM A572 Gr.65 CSA G40.21 300W CSA G40.21 400A CSA G40.21 350W ASTM A1008 SS Grade 50 ASTM A283C
Match Breakdown
CHEMISTRY MATCH
92.4%
MECHANICAL MATCH
No shared data
OVERALL
92.4%
Specifications
Property EN 10025-3 S500 AS/NZS Grade 500
Standard EN 10025-3:2019 AS/NZS 3597:2008
Category Structural Steel Structural Steel
C (%) 0.22 max max 0.2
Si (%) 0.60 max max 0.55
Mn (%) 1.80 max max 1.6
P (%) 0.025 max max 0.03
S (%) 0.020 max max 0.03
Nb (%) 0.06 max Not specified
V (%) 0.12 max Not specified
Ti (%) 0.05 max Not specified
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property EN 10025-3 S500 AS/NZS Grade 500
Tensile Strength 590-770 MPa Not specified
Yield Strength 500 MPa min Not specified
Elongation 16% min Not specified
Hardness 190-240 HB Not specified
Typical Applications
EN 10025-3 S500
Used in heavy structural sections, mining equipment, bridge fabrication, transport vehicles, and offshore structures.
AS/NZS Grade 500
Heavy mining equipment, bulldozer blades, wear-resistant structural applications, large crane booms, offshore jackets.
Key Differences
Can EN 10025-3 S500 Be Substituted With AS/NZS Grade 500?
EN 10025-3 S500 and AS/NZS Grade 500 overlap closely enough on chemistry and mechanical properties that AS/NZS Grade 500 is often considered as a substitute for EN 10025-3 S500 in many applications. Always confirm the specific property range your application needs before substituting, and check with your supplier's mill certificate.
Forms & Sizes Available on M-EX
EN 10025-3 S500
Plate → (2 listings)
Thickness: 10–10 mm (0.39–0.39 in)
Width: 1500–1500 mm (59.06–59.06 in)
Length: 2500–2800 mm (98.43–110.24 in)
AS/NZS Grade 500
Plate → (2 listings)
Thickness: 10–10 mm (0.39–0.39 in)
Width: 1500–1500 mm (59.06–59.06 in)
Length: 3100–3600 mm (122.05–141.73 in)
On M-EX Right Now
EN 10025-3 S500
2 active listings and RFQs →
AS/NZS Grade 500
2 active listings and RFQs →
Frequently Asked Questions
What is the difference between EN 10025-3 S500 and AS/NZS Grade 500?
EN 10025-3 S500 specifies Nb, V, Ti which are not specified for AS/NZS Grade 500.
Can EN 10025-3 S500 be substituted with AS/NZS Grade 500?
EN 10025-3 S500 and AS/NZS Grade 500 overlap closely enough on chemistry and mechanical properties that AS/NZS Grade 500 is often considered as a substitute for EN 10025-3 S500 in many applications. Always confirm the specific property range your application needs before substituting, and check with your supplier's mill certificate.