Post Stock Login Register

IS 11169 (Part 2) X04Cr17Ni12Mo2Ti vs ASTM A959 16-8-2H

Close Alternative — 70.4% match based on chemical composition and mechanical property overlap.

IS 11169 (Part 2) X04Cr17Ni12Mo2Ti (IS 11169 (Part 2):1989) and ASTM A959 16-8-2H (ASTM A959:2011) are both steel grades. Both fall under the Stainless Steel category. IS 11169 (Part 2) X04Cr17Ni12Mo2Ti is typically used for cold heading and cold extrusion; the standard covers wires, wire rods and bars (clause 1.1), while ASTM A959 16-8-2H is commonly used for wrought stainless steel products; recommended composition limits for adoption by product standards (clause 1.1). IS 11169 (Part 2) X04Cr17Ni12Mo2Ti is defined under Bureau of Indian Standards (IS), originating from India, while ASTM A959 16-8-2H is defined under ASTM International, originating from United States.

As per chemical composition, IS 11169 (Part 2) X04Cr17Ni12Mo2Ti vs ASTM A959 16-8-2H is a 70.4% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a close alternative overall at 70.4%.

Frequently Compared With IS 11169 (Part 2) X04Cr17Ni12Mo2Ti:
EN 10088-1 1.4301 EN 10088-1 1.4845 IS 1570 (Part 7) 12Cr13H GB/T 3280 06Cr19Ni10 GOST 5632 06Kh23N28 GOST 5632 08X18H10 EN 10088-1 1.4006 EN 10088-1 1.4401 IS 1570 (Part 7) 11Cr17Ni13W3TiH IS 1570 (Part 7) 12Cr12MoH IS 1570 (Part 7) 12Cr12MoVH IS 1570 (Part 7) 12Cr12Ni2Mo
Match Breakdown
CHEMISTRY MATCH
70.4%
MECHANICAL MATCH
No shared data
OVERALL
70.4%
Specifications
Property IS 11169 (Part 2) X04Cr17Ni12Mo2Ti ASTM A959 16-8-2H
Standard IS 11169 (Part 2):1989 ASTM A959:2011
Category Stainless Steel Stainless Steel
C (%) <=0.08 0.05-0.10
Si (%) <=1.0 <=1.00
Mn (%) <=2.0 <=2.00
Ni (%) 10.0-14.0 7.5-9.5
Cr (%) 16.0-18.0 14.5-16.5
Mo (%) 2.0-3.0 1.50-2.00
Ti (%) >=5xC, <=0.80 Not specified
S (%) <=0.030 <=0.030
P (%) <=0.045 <=0.045
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property IS 11169 (Part 2) X04Cr17Ni12Mo2Ti ASTM A959 16-8-2H
Yield Strength (0.2% proof) >=225 MPa Not specified
Tensile Strength 500-750 MPa Not specified
Elongation >=40% Not specified
Impact (U-notch 5 mm) >=60 J Not specified
Condition Quenched reference test piece (Table 6 treatment) Not specified
Typical Applications
IS 11169 (Part 2) X04Cr17Ni12Mo2Ti
Cold heading and cold extrusion; the standard covers wires, wire rods and bars (clause 1.1)
ASTM A959 16-8-2H
Wrought stainless steel products; recommended composition limits for adoption by product standards (clause 1.1)
Key Differences
Can IS 11169 (Part 2) X04Cr17Ni12Mo2Ti Be Substituted With ASTM A959 16-8-2H?
IS 11169 (Part 2) X04Cr17Ni12Mo2Ti and ASTM A959 16-8-2H are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.
On M-EX Right Now
IS 11169 (Part 2) X04Cr17Ni12Mo2Ti
0 active listings and RFQs →
ASTM A959 16-8-2H
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between IS 11169 (Part 2) X04Cr17Ni12Mo2Ti and ASTM A959 16-8-2H?
IS 11169 (Part 2) X04Cr17Ni12Mo2Ti specifies Ti which is not specified for ASTM A959 16-8-2H.
Can IS 11169 (Part 2) X04Cr17Ni12Mo2Ti be substituted with ASTM A959 16-8-2H?
IS 11169 (Part 2) X04Cr17Ni12Mo2Ti and ASTM A959 16-8-2H are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.