IS 11169 (Part 2) X04Cr17Ni12Mo2Ti vs GOST 5632 06Kh23N28
Minimal Match — 35% match
based on chemical composition and mechanical property overlap.
IS 11169 (Part 2) X04Cr17Ni12Mo2Ti (IS 11169 (Part 2):1989) and GOST 5632 06Kh23N28 (GOST 5632-2014) are both steel grades.
Both fall under the Stainless Steel category.
IS 11169 (Part 2) X04Cr17Ni12Mo2Ti is typically used for cold heading and cold extrusion; the standard covers wires, wire rods and bars (clause 1.1), while GOST 5632 06Kh23N28 is commonly used for furnace components, heat exchangers, high temperature applications.
IS 11169 (Part 2) X04Cr17Ni12Mo2Ti is defined under Bureau of Indian Standards (IS) (India).
As per chemical composition, IS 11169 (Part 2) X04Cr17Ni12Mo2Ti vs GOST 5632 06Kh23N28 is a 59.8% match.
As per mechanical properties, the match is 0%.
Combined, this makes them a minimal match overall at 35%.
Frequently Compared With IS 11169 (Part 2) X04Cr17Ni12Mo2Ti:
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property
IS 11169 (Part 2) X04Cr17Ni12Mo2Ti
GOST 5632 06Kh23N28
Yield Strength (0.2% proof)
>=225 MPa
Not specified
Tensile Strength
500-750 MPa
≥510 MPa
Elongation
>=40%
≥35%
Impact (U-notch 5 mm)
>=60 J
Not specified
Condition
Quenched reference test piece (Table 6 treatment)
Not specified
Yield Strength
Not specified
≥196 MPa
Max Service Temp
Not specified
1050°C
Typical Applications
IS 11169 (Part 2) X04Cr17Ni12Mo2Ti
Cold heading and cold extrusion; the standard covers wires, wire rods and bars (clause 1.1)
GOST 5632 06Kh23N28
Furnace components, heat exchangers, high temperature applications
Key Differences
IS 11169 (Part 2) X04Cr17Ni12Mo2Ti specifies Mo, Ti, S, P which are not specified for GOST 5632 06Kh23N28.
Can IS 11169 (Part 2) X04Cr17Ni12Mo2Ti Be Substituted With GOST 5632 06Kh23N28?
IS 11169 (Part 2) X04Cr17Ni12Mo2Ti and GOST 5632 06Kh23N28 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
What is the difference between IS 11169 (Part 2) X04Cr17Ni12Mo2Ti and GOST 5632 06Kh23N28?
IS 11169 (Part 2) X04Cr17Ni12Mo2Ti specifies Mo, Ti, S, P which are not specified for GOST 5632 06Kh23N28.
Can IS 11169 (Part 2) X04Cr17Ni12Mo2Ti be substituted with GOST 5632 06Kh23N28?
IS 11169 (Part 2) X04Cr17Ni12Mo2Ti and GOST 5632 06Kh23N28 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.