Post Stock Login Register

JIS G4303 SUS410 vs EN 10088-1 X2CrTi12

Close Alternative — 78.1% match based on chemical composition and mechanical property overlap.

JIS G4303 SUS410 (JIS G4303:2021) and EN 10088-1 X2CrTi12 (EN 10088-1:2023) are both steel grades. Both fall under the Stainless Steel category. JIS G4303 SUS410 is defined under Japanese Industrial Standards (JIS), originating from Japan, while EN 10088-1 X2CrTi12 is defined under European Standard (EN), originating from Europe.

As per chemical composition, JIS G4303 SUS410 vs EN 10088-1 X2CrTi12 is a 78.1% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a close alternative overall at 78.1%.

Frequently Compared With JIS G4303 SUS410:
GB/T 3280 06Cr19Ni10 GOST 5632 06Kh23N28 GOST 5632 12Kh13 EN 10088-1 1.4301 EN 10088-1 1.4401 GOST 5632 08X18H10 EN 10088-1 1.4845 EN 10088-1 1.4006 IS 1570 (Part 7) 11Cr17Ni13W3TiH IS 1570 (Part 7) 12Cr12MoH IS 1570 (Part 7) 12Cr12MoVH ASTM A959 .-
Match Breakdown
CHEMISTRY MATCH
78.1%
MECHANICAL MATCH
No shared data
OVERALL
78.1%
Specifications
Property JIS G4303 SUS410 EN 10088-1 X2CrTi12
Standard JIS G4303:2021 EN 10088-1:2023
Category Stainless Steel Stainless Steel
C (%) ≤0.15 <=0.030
Si (%) ≤1.00 <=1.00
Mn (%) ≤1.00 <=1.00
Cr (%) 11.5–13.5 10.5-12.5
Ni (%) ≤0.60 Not specified
P (%) ≤0.040 <=0.040
S (%) ≤0.030 <=0.015
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property JIS G4303 SUS410 EN 10088-1 X2CrTi12
Tensile Strength ≥480 MPa (annealed) Not specified
Hardness HRC 36–45 (hardened) Not specified
Elongation ≥20% Not specified
Typical Applications
JIS G4303 SUS410
Cutlery, surgical instruments, turbine blades, fasteners
EN 10088-1 X2CrTi12
Not documented
Key Differences
Can JIS G4303 SUS410 Be Substituted With EN 10088-1 X2CrTi12?
JIS G4303 SUS410 and EN 10088-1 X2CrTi12 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.
Forms & Sizes Available on M-EX
JIS G4303 SUS410
Sheet → (3 listings)
Thickness: 6–6 mm (0.24–0.24 in)
Width: 1250–1250 mm (49.21–49.21 in)
Length: 2500–3100 mm (98.43–122.05 in)
EN 10088-1 X2CrTi12
No active listings currently.
On M-EX Right Now
JIS G4303 SUS410
3 active listings and RFQs →
EN 10088-1 X2CrTi12
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between JIS G4303 SUS410 and EN 10088-1 X2CrTi12?
JIS G4303 SUS410 specifies Ni which is not specified for EN 10088-1 X2CrTi12.
Can JIS G4303 SUS410 be substituted with EN 10088-1 X2CrTi12?
JIS G4303 SUS410 and EN 10088-1 X2CrTi12 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.