Post Stock Login Register

JIS G4303 SUS410 vs ASTM A959 .-

Minimal Match — 35% match based on chemical composition and mechanical property overlap.

JIS G4303 SUS410 (JIS G4303:2021) and ASTM A959 .- (ASTM A959:2011) are both steel grades. Both fall under the Stainless Steel category. JIS G4303 SUS410 is typically used for cutlery, surgical instruments, turbine blades, fasteners, while ASTM A959 .- is commonly used for wrought stainless steel products; recommended composition limits for adoption by product standards (clause 1.1). JIS G4303 SUS410 is defined under Japanese Industrial Standards (JIS), originating from Japan, while ASTM A959 .- is defined under ASTM International, originating from United States.

As per chemical composition, JIS G4303 SUS410 vs ASTM A959 .- is a 60.8% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a minimal match overall at 35%.

Frequently Compared With JIS G4303 SUS410:
GB/T 3280 06Cr19Ni10 GOST 5632 06Kh23N28 GOST 5632 12Kh13 EN 10088-1 1.4301 EN 10088-1 1.4401 GOST 5632 08X18H10 EN 10088-1 1.4845 EN 10088-1 1.4006 IS 1570 (Part 7) 11Cr17Ni13W3TiH IS 1570 (Part 7) 12Cr12MoH IS 1570 (Part 7) 12Cr12MoVH IS 1570 (Part 7) 12Cr12Ni2Mo
Match Breakdown
CHEMISTRY MATCH
60.8%
MECHANICAL MATCH
No shared data
OVERALL
35%
Specifications
Property JIS G4303 SUS410 ASTM A959 .-
Standard JIS G4303:2021 ASTM A959:2011
Category Stainless Steel Stainless Steel
C (%) ≤0.15 <=0.030
Si (%) ≤1.00 <=1.00
Mn (%) ≤1.00 <=1.00
Cr (%) 11.5–13.5 18.0-20.0
Ni (%) ≤0.60 <=0.50
P (%) ≤0.040 <=0.040
S (%) ≤0.030 <=0.030
Cb (%) Not specified 0.10-0.60
N (%) Not specified <=0.030
Ti (%) Not specified 0.07-0.30
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property JIS G4303 SUS410 ASTM A959 .-
Tensile Strength ≥480 MPa (annealed) Not specified
Hardness HRC 36–45 (hardened) Not specified
Elongation ≥20% Not specified
Typical Applications
JIS G4303 SUS410
Cutlery, surgical instruments, turbine blades, fasteners
ASTM A959 .-
Wrought stainless steel products; recommended composition limits for adoption by product standards (clause 1.1)
Key Differences
Can JIS G4303 SUS410 Be Substituted With ASTM A959 .-?
JIS G4303 SUS410 and ASTM A959 .- share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
Forms & Sizes Available on M-EX
JIS G4303 SUS410
Sheet → (3 listings)
Thickness: 6–6 mm (0.24–0.24 in)
Width: 1250–1250 mm (49.21–49.21 in)
Length: 2500–3100 mm (98.43–122.05 in)
ASTM A959 .-
No active listings currently.
On M-EX Right Now
JIS G4303 SUS410
3 active listings and RFQs →
ASTM A959 .-
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between JIS G4303 SUS410 and ASTM A959 .-?
ASTM A959 .- specifies Cb, N, Ti which are not specified for JIS G4303 SUS410.
Can JIS G4303 SUS410 be substituted with ASTM A959 .-?
JIS G4303 SUS410 and ASTM A959 .- share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.