Post Stock Login Register

EN 10025-2 E295 vs SAE J403 1002

Related Material — 65% match based on chemical composition and mechanical property overlap.

EN 10025-2 E295 (EN 10025-2:2019) and SAE J403 1002 (SAE J403:2014) are both steel grades. EN 10025-2 E295 is classified under Structural Steel, while SAE J403 1002 is classified under Carbon Steel — a different category, which is worth noting alongside the chemistry match below. EN 10025-2 E295 is typically used for hot rolled products of structural steels, while SAE J403 1002 is commonly used for chemistry-only grade; product scope as listed in the composition notes. EN 10025-2 E295 is defined under European Standard (EN), originating from Europe, while SAE J403 1002 is defined under SAE International, originating from United States.

As per chemical composition, EN 10025-2 E295 vs SAE J403 1002 is a 87.2% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a related material overall at 65%.

Frequently Compared With EN 10025-2 E295:
GOST 19281 09G2S CSA G40.21 260W AS/NZS 3679.1 300 CSA G40.21 300W AS/NZS 3679.1 350 CSA G40.21 350W CSA G40.21 400A CSA G40.21 400W CSA G40.21 480W ASTM A1008 SS Grade 50 ASTM A1008 SS Grade 80 ASTM A283C
Match Breakdown
CHEMISTRY MATCH
87.2%
MECHANICAL MATCH
No shared data
OVERALL
65%
Specifications
Property EN 10025-2 E295 SAE J403 1002
Standard EN 10025-2:2019 SAE J403:2014
Category Structural Steel Carbon Steel
P (%) <=0.045 <=0.030 (flat rolled), <=0.040 (long products)
S (%) <=0.045 <=0.035 (flat rolled), <=0.050 (long products)
N (%) <=0.012 Not specified
C (%) Not specified 0.02-0.04
Mn (%) Not specified <=0.35
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property EN 10025-2 E295 SAE J403 1002
Tensile Strength 470-610 MPa Not specified
Yield Strength >=295 MPa Not specified
Elongation >=20% Not specified
Condition Nominal thickness up to 16 mm (tensile for 3 to 100 mm, elongation for 3 to 40 mm), longitudinal test pieces Not specified
Typical Applications
EN 10025-2 E295
Hot rolled products of structural steels
SAE J403 1002
Chemistry-only grade; product scope as listed in the composition notes
Key Differences
Can EN 10025-2 E295 Be Substituted With SAE J403 1002?
EN 10025-2 E295 and SAE J403 1002 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
On M-EX Right Now
EN 10025-2 E295
0 active listings and RFQs →
SAE J403 1002
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between EN 10025-2 E295 and SAE J403 1002?
Different category: EN 10025-2 E295 is Structural Steel, SAE J403 1002 is Carbon Steel. EN 10025-2 E295 specifies N which is not specified for SAE J403 1002. SAE J403 1002 specifies C, Mn which are not specified for EN 10025-2 E295.
Can EN 10025-2 E295 be substituted with SAE J403 1002?
EN 10025-2 E295 and SAE J403 1002 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.