Post Stock Login Register

EN 10025-2 E360 vs ASTM A36

Related Material — 61% match based on chemical composition and mechanical property overlap.

EN 10025-2 E360 (EN 10025-2:2019) and ASTM A36 (ASTM A36) are both steel grades. EN 10025-2 E360 is classified under Structural Steel, while ASTM A36 is classified under Carbon Steel — a different category, which is worth noting alongside the chemistry match below. EN 10025-2 E360 is typically used for hot rolled products of structural steels, while ASTM A36 is commonly used for structural fabrication, bridges, buildings, machinery parts, flanges. EN 10025-2 E360 is defined under European Standard (EN), originating from Europe, while ASTM A36 is defined under ASTM International, originating from United States.

As per chemical composition, EN 10025-2 E360 vs ASTM A36 is a 91.5% match. As per mechanical properties, the match is 0%. Combined, this makes them a related material overall at 61%.

Frequently Compared With EN 10025-2 E360:
GOST 19281 09G2S CSA G40.21 260W AS/NZS 3679.1 300 CSA G40.21 300W AS/NZS 3679.1 350 CSA G40.21 350W CSA G40.21 400W CSA G40.21 480W ASTM A1008 SS Grade 50 ASTM A1008 SS Grade 80 ASTM A283C ASTM A572 Gr.65
Match Breakdown
CHEMISTRY MATCH
91.5%
MECHANICAL MATCH
0%
OVERALL
61%
Specifications
Property EN 10025-2 E360 ASTM A36
Standard EN 10025-2:2019 ASTM A36
Category Structural Steel Carbon Steel
P (%) <=0.045 ≤0.040
S (%) <=0.045 ≤0.050
N (%) <=0.012 Not specified
C (%) Not specified ≤0.26
Mn (%) Not specified ≤1.20
Si (%) Not specified 0.15–0.40
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property EN 10025-2 E360 ASTM A36
Tensile Strength 670-830 MPa 400–550 MPa
Yield Strength >=360 MPa 250 MPa min
Elongation >=11% ≥23%
Condition Nominal thickness up to 16 mm (tensile for 3 to 100 mm, elongation for 3 to 40 mm), longitudinal test pieces Not specified
Typical Applications
EN 10025-2 E360
Hot rolled products of structural steels
ASTM A36
Structural fabrication, bridges, buildings, machinery parts, flanges
Key Differences
Can EN 10025-2 E360 Be Substituted With ASTM A36?
EN 10025-2 E360 and ASTM A36 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
Forms & Sizes Available on M-EX
EN 10025-2 E360
No active listings currently.
ASTM A36
Round Bar → (2 listings)
Diameter: 40–40 mm (1.57–1.57 in)
Length: 5600–6500 mm (220.47–255.91 in)
Plate → (2 listings)
Thickness: 10–10 mm (0.39–0.39 in)
Width: 1500–1500 mm (59.06–59.06 in)
Length: 2500–2700 mm (98.43–106.3 in)
On M-EX Right Now
EN 10025-2 E360
0 active listings and RFQs →
ASTM A36
4 active listings and RFQs →
Frequently Asked Questions
What is the difference between EN 10025-2 E360 and ASTM A36?
Different category: EN 10025-2 E360 is Structural Steel, ASTM A36 is Carbon Steel. EN 10025-2 E360 specifies N which is not specified for ASTM A36. ASTM A36 specifies C, Mn, Si which are not specified for EN 10025-2 E360.
Can EN 10025-2 E360 be substituted with ASTM A36?
EN 10025-2 E360 and ASTM A36 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.