Post Stock Login Register

IS 11169 (Part 2) X04Cr17Ni12Mo2Ti vs ASTM A959 SS316

Strong Match — 100% match based on chemical composition and mechanical property overlap.

IS 11169 (Part 2) X04Cr17Ni12Mo2Ti (IS 11169 (Part 2):1989) and ASTM A959 SS316 (ASTM A959:2011) are both steel grades. Both fall under the Stainless Steel category. IS 11169 (Part 2) X04Cr17Ni12Mo2Ti is typically used for cold heading and cold extrusion; the standard covers wires, wire rods and bars (clause 1.1), while ASTM A959 SS316 is commonly used for marine, chemical, pharmaceutical, food processing equipment. IS 11169 (Part 2) X04Cr17Ni12Mo2Ti is defined under Bureau of Indian Standards (IS), originating from India, while ASTM A959 SS316 is defined under ASTM International, originating from United States.

As per chemical composition, IS 11169 (Part 2) X04Cr17Ni12Mo2Ti vs ASTM A959 SS316 is a 100% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a strong match overall at 100%.

Frequently Compared With IS 11169 (Part 2) X04Cr17Ni12Mo2Ti:
ASTM A959 16-8-2H EN 10088-1 1.4301 EN 10088-1 1.4845 IS 1570 (Part 7) 11Cr17Ni13W3TiH IS 1570 (Part 7) 12Cr13H GB/T 3280 06Cr19Ni10 GOST 5632 06Kh23N28 GOST 5632 08X18H10 EN 10088-1 1.4006 EN 10088-1 1.4401 IS 1570 (Part 7) 12Cr12MoH IS 1570 (Part 7) 12Cr12MoVH
Match Breakdown
CHEMISTRY MATCH
100%
MECHANICAL MATCH
No shared data
OVERALL
100%
Specifications
Property IS 11169 (Part 2) X04Cr17Ni12Mo2Ti ASTM A959 SS316
Standard IS 11169 (Part 2):1989 ASTM A959:2011
Category Stainless Steel Stainless Steel
C (%) <=0.08 <=0.08
Si (%) <=1.0 <=1.00
Mn (%) <=2.0 <=2.00
Ni (%) 10.0-14.0 10.0-14.0
Cr (%) 16.0-18.0 16.0-18.0
Mo (%) 2.0-3.0 2.00-3.00
Ti (%) >=5xC, <=0.80 Not specified
S (%) <=0.030 <=0.030
P (%) <=0.045 <=0.045
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property IS 11169 (Part 2) X04Cr17Ni12Mo2Ti ASTM A959 SS316
Yield Strength (0.2% proof) >=225 MPa Not specified
Tensile Strength 500-750 MPa Not specified
Elongation >=40% Not specified
Impact (U-notch 5 mm) >=60 J Not specified
Condition Quenched reference test piece (Table 6 treatment) Not specified
Typical Applications
IS 11169 (Part 2) X04Cr17Ni12Mo2Ti
Cold heading and cold extrusion; the standard covers wires, wire rods and bars (clause 1.1)
ASTM A959 SS316
Marine, chemical, pharmaceutical, food processing equipment
Key Differences
Can IS 11169 (Part 2) X04Cr17Ni12Mo2Ti Be Substituted With ASTM A959 SS316?
IS 11169 (Part 2) X04Cr17Ni12Mo2Ti and ASTM A959 SS316 overlap closely enough on chemistry and mechanical properties that ASTM A959 SS316 is often considered as a substitute for IS 11169 (Part 2) X04Cr17Ni12Mo2Ti in many applications. Always confirm the specific property range your application needs before substituting, and check with your supplier's mill certificate.
Forms & Sizes Available on M-EX
IS 11169 (Part 2) X04Cr17Ni12Mo2Ti
No active listings currently.
ASTM A959 SS316
Sheet → (24 listings)
Thickness: 2–6 mm (0.08–0.24 in)
Width: 1250–1250 mm (49.21–49.21 in)
Length: 2500–4000 mm (98.43–157.48 in)
Plate → (6 listings)
Thickness: 10–10 mm (0.39–0.39 in)
Width: 1500–1500 mm (59.06–59.06 in)
Length: 2600–4200 mm (102.36–165.35 in)
Round Bar → (3 listings)
Diameter: 40–40 mm (1.57–1.57 in)
Length: 2500–4200 mm (98.43–165.35 in)
On M-EX Right Now
IS 11169 (Part 2) X04Cr17Ni12Mo2Ti
0 active listings and RFQs →
ASTM A959 SS316
33 active listings and RFQs →
Frequently Asked Questions
What is the difference between IS 11169 (Part 2) X04Cr17Ni12Mo2Ti and ASTM A959 SS316?
IS 11169 (Part 2) X04Cr17Ni12Mo2Ti specifies Ti which is not specified for ASTM A959 SS316.
Can IS 11169 (Part 2) X04Cr17Ni12Mo2Ti be substituted with ASTM A959 SS316?
IS 11169 (Part 2) X04Cr17Ni12Mo2Ti and ASTM A959 SS316 overlap closely enough on chemistry and mechanical properties that ASTM A959 SS316 is often considered as a substitute for IS 11169 (Part 2) X04Cr17Ni12Mo2Ti in many applications. Always confirm the specific property range your application needs before substituting, and check with your supplier's mill certificate.