Post Stock Login Register

IS 11169 (Part 2) X04Ni25Cr15Ti2Mo1VB vs ASTM A959 622

Related Material — 69.9% match based on chemical composition and mechanical property overlap.

IS 11169 (Part 2) X04Ni25Cr15Ti2Mo1VB (IS 11169 (Part 2):2023) and ASTM A959 622 (ASTM A959:2011) are both steel grades. Both fall under the Stainless Steel category. IS 11169 (Part 2) X04Ni25Cr15Ti2Mo1VB is typically used for cold heading and cold extrusion of stainless steel parts; the standard covers wires, wire rods and bars of 0.8 to 50 mm (clause 1.1, table 11), while ASTM A959 622 is commonly used for wrought stainless steel products; recommended composition limits for adoption by product standards (clause 1.1). IS 11169 (Part 2) X04Ni25Cr15Ti2Mo1VB is defined under Bureau of Indian Standards (IS), originating from India, while ASTM A959 622 is defined under ASTM International, originating from United States.

As per chemical composition, IS 11169 (Part 2) X04Ni25Cr15Ti2Mo1VB vs ASTM A959 622 is a 70.1% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a related material overall at 69.9%.

Frequently Compared With IS 11169 (Part 2) X04Ni25Cr15Ti2Mo1VB:
EN 10088-1 1.4301 GB/T 3280 06Cr19Ni10 GOST 5632 06Kh23N28 GOST 5632 08X18H10 EN 10088-1 1.4006 EN 10088-1 1.4845 IS 1570 (Part 7) 12Cr12MoH EN 10088-1 1.4401 IS 1570 (Part 7) 11Cr17Ni13W3TiH IS 1570 (Part 7) 12Cr12MoVH IS 1570 (Part 7) 12Cr12Ni2Mo GOST 5632 12Kh13
Match Breakdown
CHEMISTRY MATCH
70.1%
MECHANICAL MATCH
No shared data
OVERALL
69.9%
Specifications
Property IS 11169 (Part 2) X04Ni25Cr15Ti2Mo1VB ASTM A959 622
Standard IS 11169 (Part 2):2023 ASTM A959:2011
Category Stainless Steel Stainless Steel
Al (%) <=0.35 <=0.35
B (%) 0.001-0.010 0.001-0.010
C (%) <=0.08 <=0.08
Cr (%) 13.5-16.0 12.0-15.0
Mn (%) <=2.00 <=1.50
Mo (%) 1.00-1.50 2.5-3.5
Ni (%) 24.0-27.0 24.0-28.0
P (%) <=0.040 <=0.040
S (%) <=0.030 <=0.030
Si (%) <=1.00 <=1.00
Ti (%) 1.90-2.35 1.55-2.00
V (%) 0.10-0.50 Not specified
Cu (%) Not specified <=0.50
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property IS 11169 (Part 2) X04Ni25Cr15Ti2Mo1VB ASTM A959 622
Reduction of Area, cold drawn and solution annealed (+AT+C+AT) >=65% (0.8 to 5 mm) Not specified
Tensile Strength, cold drawn and solution annealed (+AT+C+AT) <=780 MPa (0.8 to 2 mm) / <=730 MPa (over 2 to 5 mm) Not specified
Typical Applications
IS 11169 (Part 2) X04Ni25Cr15Ti2Mo1VB
Cold heading and cold extrusion of stainless steel parts; the standard covers wires, wire rods and bars of 0.8 to 50 mm (clause 1.1, Table 11)
ASTM A959 622
Wrought stainless steel products; recommended composition limits for adoption by product standards (clause 1.1)
Key Differences
Can IS 11169 (Part 2) X04Ni25Cr15Ti2Mo1VB Be Substituted With ASTM A959 622?
IS 11169 (Part 2) X04Ni25Cr15Ti2Mo1VB and ASTM A959 622 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.
On M-EX Right Now
IS 11169 (Part 2) X04Ni25Cr15Ti2Mo1VB
0 active listings and RFQs →
ASTM A959 622
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between IS 11169 (Part 2) X04Ni25Cr15Ti2Mo1VB and ASTM A959 622?
IS 11169 (Part 2) X04Ni25Cr15Ti2Mo1VB specifies V which is not specified for ASTM A959 622. ASTM A959 622 specifies Cu which is not specified for IS 11169 (Part 2) X04Ni25Cr15Ti2Mo1VB.
Can IS 11169 (Part 2) X04Ni25Cr15Ti2Mo1VB be substituted with ASTM A959 622?
IS 11169 (Part 2) X04Ni25Cr15Ti2Mo1VB and ASTM A959 622 share some compositional similarity but differ enough that substitution should not be assumed. Review the differences above carefully, and consult the applicable standard or a metallurgist before using one in place of the other.