Post Stock Login Register

IS 11169 (Part 2) X04Ni25Cr15Ti2Mo1VB vs EN 10088-1 X5NiCrTiMoVB25-15-2

Strong Match — 92.8% match based on chemical composition and mechanical property overlap.

IS 11169 (Part 2) X04Ni25Cr15Ti2Mo1VB (IS 11169 (Part 2):2023) and EN 10088-1 X5NiCrTiMoVB25-15-2 (EN 10088-1:2023) are both steel grades. Both fall under the Stainless Steel category. IS 11169 (Part 2) X04Ni25Cr15Ti2Mo1VB is defined under Bureau of Indian Standards (IS), originating from India, while EN 10088-1 X5NiCrTiMoVB25-15-2 is defined under European Standard (EN), originating from Europe.

As per chemical composition, IS 11169 (Part 2) X04Ni25Cr15Ti2Mo1VB vs EN 10088-1 X5NiCrTiMoVB25-15-2 is a 92.8% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a strong match overall at 92.8%.

Frequently Compared With IS 11169 (Part 2) X04Ni25Cr15Ti2Mo1VB:
EN 10088-1 1.4301 GOST 5632 06Kh23N28 EN 10088-1 1.4006 EN 10088-1 1.4845 GB/T 3280 06Cr19Ni10 GOST 5632 08X18H10 EN 10088-1 1.4401 IS 1570 (Part 7) 11Cr17Ni13W3TiH IS 1570 (Part 7) 12Cr12MoH GOST 5632 12Kh13 IS 1570 (Part 7) 12Cr12MoVH IS 1570 (Part 7) 12Cr12Ni2Mo
Match Breakdown
CHEMISTRY MATCH
92.8%
MECHANICAL MATCH
No shared data
OVERALL
92.8%
Specifications
Property IS 11169 (Part 2) X04Ni25Cr15Ti2Mo1VB EN 10088-1 X5NiCrTiMoVB25-15-2
Standard IS 11169 (Part 2):2023 EN 10088-1:2023
Category Stainless Steel Stainless Steel
Al (%) <=0.35 <=0.35
B (%) 0.001-0.010 0.0010-0.010
C (%) <=0.08 <=0.08
Cr (%) 13.5-16.0 13.0-16.0
Mn (%) <=2.00 1.00-2.00
Mo (%) 1.00-1.50 1.00-1.50
Ni (%) 24.0-27.0 24.0-27.0
P (%) <=0.040 <=0.025
S (%) <=0.030 <=0.015
Si (%) <=1.00 <=1.00
Ti (%) 1.90-2.35 1.90-2.30
V (%) 0.10-0.50 0.10-0.50
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property IS 11169 (Part 2) X04Ni25Cr15Ti2Mo1VB EN 10088-1 X5NiCrTiMoVB25-15-2
Reduction of Area, cold drawn and solution annealed (+AT+C+AT) >=65% (0.8 to 5 mm) Not specified
Tensile Strength, cold drawn and solution annealed (+AT+C+AT) <=780 MPa (0.8 to 2 mm) / <=730 MPa (over 2 to 5 mm) Not specified
Typical Applications
IS 11169 (Part 2) X04Ni25Cr15Ti2Mo1VB
Cold heading and cold extrusion of stainless steel parts; the standard covers wires, wire rods and bars of 0.8 to 50 mm (clause 1.1, Table 11)
EN 10088-1 X5NiCrTiMoVB25-15-2
Not documented
Can IS 11169 (Part 2) X04Ni25Cr15Ti2Mo1VB Be Substituted With EN 10088-1 X5NiCrTiMoVB25-15-2?
IS 11169 (Part 2) X04Ni25Cr15Ti2Mo1VB and EN 10088-1 X5NiCrTiMoVB25-15-2 overlap closely enough on chemistry and mechanical properties that EN 10088-1 X5NiCrTiMoVB25-15-2 is often considered as a substitute for IS 11169 (Part 2) X04Ni25Cr15Ti2Mo1VB in many applications. Always confirm the specific property range your application needs before substituting, and check with your supplier's mill certificate.
On M-EX Right Now
IS 11169 (Part 2) X04Ni25Cr15Ti2Mo1VB
0 active listings and RFQs →
EN 10088-1 X5NiCrTiMoVB25-15-2
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between IS 11169 (Part 2) X04Ni25Cr15Ti2Mo1VB and EN 10088-1 X5NiCrTiMoVB25-15-2?
Both grades share a similar composition profile; see the specification table above for the exact chemistry and mechanical property values.
Can IS 11169 (Part 2) X04Ni25Cr15Ti2Mo1VB be substituted with EN 10088-1 X5NiCrTiMoVB25-15-2?
IS 11169 (Part 2) X04Ni25Cr15Ti2Mo1VB and EN 10088-1 X5NiCrTiMoVB25-15-2 overlap closely enough on chemistry and mechanical properties that EN 10088-1 X5NiCrTiMoVB25-15-2 is often considered as a substitute for IS 11169 (Part 2) X04Ni25Cr15Ti2Mo1VB in many applications. Always confirm the specific property range your application needs before substituting, and check with your supplier's mill certificate.