Post Stock Login Register

GOST 5632 08X18H10 vs EN 10088-1 X3CrNiCu18-9-4

Close Alternative — 76.5% match based on chemical composition and mechanical property overlap.

GOST 5632 08X18H10 (GOST 5632-2014) and EN 10088-1 X3CrNiCu18-9-4 (EN 10088-1:2014) are both steel grades. Both fall under the Stainless Steel category. EN 10088-1 X3CrNiCu18-9-4 is defined under European Standard (EN) (Europe).

As per chemical composition, GOST 5632 08X18H10 vs EN 10088-1 X3CrNiCu18-9-4 is a 76.5% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a close alternative overall at 76.5%.

Frequently Compared With GOST 5632 08X18H10:
EN 10088-1 1.4301 EN 10088-1 1.4845 EN 10088-1 1.4006 EN 10088-1 1.4401 ASTM A959 16-8-2H ASTM A959 201 ASTM A959 202 ASTM A959 .- IS 1570 (Part 7) 11Cr17Ni13W3TiH IS 1570 (Part 7) 20Cr12MoNiVH ASTM A959 26-3-3 IS 1570 (Part 7) 12Cr12Ni2Mo
Match Breakdown
CHEMISTRY MATCH
76.5%
MECHANICAL MATCH
No shared data
OVERALL
76.5%
Specifications
Property GOST 5632 08X18H10 EN 10088-1 X3CrNiCu18-9-4
Standard GOST 5632-2014 EN 10088-1:2014
Category Stainless Steel Stainless Steel
C (%) ≤0.08 <=0.04
Si (%) ≤0.80 <=1.00
Mn (%) ≤2.00 <=2.00
Cr (%) 17.0–19.0 17.0-19.0
Ni (%) 9.0–11.0 8.5-10.5
S (%) ≤0.020 <=0.015
P (%) ≤0.035 <=0.045
N (%) Not specified <=0.10
Cu (%) Not specified 3.0-4.0
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property GOST 5632 08X18H10 EN 10088-1 X3CrNiCu18-9-4
Tensile Strength ≥520 MPa Not specified
Yield Strength ≥205 MPa Not specified
Elongation ≥40% Not specified
Typical Applications
GOST 5632 08X18H10
Chemical equipment, food processing, general corrosion resistant applications
EN 10088-1 X3CrNiCu18-9-4
Not documented
Key Differences
Can GOST 5632 08X18H10 Be Substituted With EN 10088-1 X3CrNiCu18-9-4?
GOST 5632 08X18H10 and EN 10088-1 X3CrNiCu18-9-4 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.
Forms & Sizes Available on M-EX
GOST 5632 08X18H10
Sheet → (2 listings)
Thickness: 6–6 mm (0.24–0.24 in)
Width: 1250–1250 mm (49.21–49.21 in)
Length: 2500–2700 mm (98.43–106.3 in)
EN 10088-1 X3CrNiCu18-9-4
No active listings currently.
On M-EX Right Now
GOST 5632 08X18H10
2 active listings and RFQs →
EN 10088-1 X3CrNiCu18-9-4
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between GOST 5632 08X18H10 and EN 10088-1 X3CrNiCu18-9-4?
EN 10088-1 X3CrNiCu18-9-4 specifies N, Cu which are not specified for GOST 5632 08X18H10.
Can GOST 5632 08X18H10 be substituted with EN 10088-1 X3CrNiCu18-9-4?
GOST 5632 08X18H10 and EN 10088-1 X3CrNiCu18-9-4 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.