Post Stock Login Register

GOST 5632 12Kh13 vs EN 10088-1 X15Cr13

Close Alternative — 81.7% match based on chemical composition and mechanical property overlap.

GOST 5632 12Kh13 (GOST 5632-2014) and EN 10088-1 X15Cr13 (EN 10088-1:2023) are both steel grades. Both fall under the Stainless Steel category. EN 10088-1 X15Cr13 is defined under European Standard (EN) (Europe).

As per chemical composition, GOST 5632 12Kh13 vs EN 10088-1 X15Cr13 is a 81.7% match. Mechanical property data is not available for both grades, so this factor could not be scored. Combined, this makes them a close alternative overall at 81.7%.

Frequently Compared With GOST 5632 12Kh13:
EN 10088-1 1.4006 EN 10088-1 1.4401 EN 10088-1 1.4301 EN 10088-1 1.4845 ASTM A959 .- GB/T 3280 06Cr19Ni10 IS 1570 (Part 7) 11Cr17Ni13W3TiH IS 1570 (Part 7) 12Cr12Ni2Mo IS 1570 (Part 7) 12Cr13H IS 1570 (Part 7) 20Cr12MoNiVH IS 1570 (Part 7) 12Cr12MoH IS 1570 (Part 7) 12Cr12MoVH
Match Breakdown
CHEMISTRY MATCH
81.7%
MECHANICAL MATCH
No shared data
OVERALL
81.7%
Specifications
Property GOST 5632 12Kh13 EN 10088-1 X15Cr13
Standard GOST 5632-2014 EN 10088-1:2023
Category Stainless Steel Stainless Steel
C (%) 0.09–0.15 0.12-0.17
Si (%) ≤0.80 <=1.00
Mn (%) ≤0.80 <=1.00
Cr (%) 12.0–14.0 12.0-14.0
Ni (%) ≤0.60 Not specified
P (%) Not specified <=0.040
S (%) Not specified <=0.015
Matched by chemical composition and mechanical properties, not a formal equivalence claim. Always verify against the applicable standard before substitution.
Mechanical Properties
Property GOST 5632 12Kh13 EN 10088-1 X15Cr13
Tensile Strength ≥540 MPa (annealed) Not specified
Hardness HRC 36–45 (hardened) Not specified
Typical Applications
GOST 5632 12Kh13
Turbine blades, pump shafts, fasteners, cutlery
EN 10088-1 X15Cr13
Not documented
Key Differences
Can GOST 5632 12Kh13 Be Substituted With EN 10088-1 X15Cr13?
GOST 5632 12Kh13 and EN 10088-1 X15Cr13 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.
Forms & Sizes Available on M-EX
GOST 5632 12Kh13
Sheet → (2 listings)
Thickness: 6–6 mm (0.24–0.24 in)
Width: 1250–1250 mm (49.21–49.21 in)
Length: 2700–3400 mm (106.3–133.86 in)
EN 10088-1 X15Cr13
No active listings currently.
On M-EX Right Now
GOST 5632 12Kh13
2 active listings and RFQs →
EN 10088-1 X15Cr13
0 active listings and RFQs →
Frequently Asked Questions
What is the difference between GOST 5632 12Kh13 and EN 10088-1 X15Cr13?
GOST 5632 12Kh13 specifies Ni which is not specified for EN 10088-1 X15Cr13. EN 10088-1 X15Cr13 specifies P, S which are not specified for GOST 5632 12Kh13.
Can GOST 5632 12Kh13 be substituted with EN 10088-1 X15Cr13?
GOST 5632 12Kh13 and EN 10088-1 X15Cr13 are a close alternative rather than a direct substitute. Some properties overlap well, but check the specific chemistry and mechanical rows above against your application's requirements before treating them as interchangeable.